บริษัท ทริปเปิ้ล อี เทรดดิ้ง จำกัด

H5CX-A11SD-N OMRON

฿0.00

H5CX-A11SD-N OMRON

จำนวน

เหลือ 0 ชิ้น

หมวดหมู่ : Timers
รหัสสินค้า : 007043

รายละเอียดสินค้า H5CX-A11SD-N OMRON

**Ratings**
Rated supply voltage	24 VAC 50/60 Hz 12 to 24 VDC Permissible ripple: 20% max.
Operating voltage range	85% to 110% of rated supply voltage (90% to 110% at 12 VDC)
Power consumption	Approx. 5.1 VA (at 24 VAC) Approx. 2.4 W (at 24 VDC) Note: Inrush current will flow for a short time when the power supply is turned ON. Inrush Current (Reference Values) 6.4 A (peak value) (Applied voltage: 26.4 VAC, Time: 1.4 ms) 4.4 A (peak value) (Applied voltage: 26.4 VDC, Time: 1.7 ms)
Time ranges (Number of ranges)	10
Time ranges	0.001 s to 9.999 s, 0.01 s to 99.99 s, 0.1 s to 999.9 s, 1 s to 9999 s, 0.1 min to 999.9 min, 1 min to 9999 min, 0.1 h to 999.9 h, 1 h to 9999 h, 1s to 99min59s, 1min to 99h59min
Select method	Dip switch or Operation Key
Input signals	Signal, Gate, Reset
Input method	No-voltage/Voltage input (Switchable)
No-voltage input (Solid state input)	ON impedance: 1 kOhm max. Leakage current: Approx. 12 mA ON residual voltage: 3 V max. OFF impedance: 100 kOhm min. (The DC voltage must be 30 VDC max.)
No-voltage input (Contact input)	Use contact which can adequately switch 5 mA at 10 V (The DC voltage must be 30 VDC max.)
No-voltage input (Applicable two-wire sensor)	Leakage current: 1.5 mA max. Switching capacity: 5 mA min. Residual voltage: 3.0 VDC max. Operating voltage: 10 VDC
Voltage input	High: 4.5 to 30 VDC Low: 0 to 2 VDC Input resistance: 4.7 kOhm (The DC voltage must be 30 VDC max.)
Minimum input signal width	1 ms/ 20 ms (Switchable) (Signal, Reset, Gate)
Standby time	250 ms max. (Control output is turned OFF and no input is accepted during sensor waiting time.)
Output modes	A (Signal ON delay 1), A-1 (Signal ON delay 2), A-2 (Power ON delay 1), A-3 (Power ON delay 2), b (Repeat cycle 1), b-1 (Repeat cycle 2), d (Signal OFF delay), E (Interval), F (Cumulative), Z (ON/OFF-duty adjustable flicker), S (Stopwatch), toff (Flicker OFF start 1), ton (Flicker ON start 1), toff-1 (Flicker OFF start 2), ton-1 (Flicker ON start 2)
Control output (Solid state output)	Transistor output (NPN open collector) Switching capacities: 100 mA max. 30 VDC max. Residual voltage: 1.5 VDC max. (Ability: Approx. 1 V) Leakage current: 0.1 mA max.
One-shot output time	0.01 to 99.99 s
Reset system	Power reset(A,A-1,A-2,b,d,E,Z,S,ton,toff mode), Automatic reset(A-1,b,b-1,d,E,Z,ton,toff,S,ton-1,toff-1 mode), External reset, Manual reset
Power reset	Minimum power-opening time: 0.5 s (except for A-3, b-1, F, ton-1 and toff-1 mode)
Timer mode	Elapsed time (UP) and remaining time (DOWN) (selectable)
Display method	7-segment negative transmissive LCD
Digit	4 digits
Character height	Present value: 12 mm (Red) Zero suppression: Equipped Set value: 6 mm (Green)
Key protect Method	Key protect Switch
Memory backup Methods	EEP-ROM (Number of rewite: 100000 times min., Service life: 10 years min.)
Ambient temperature	Operating: -10 to 55 CEL When mount timer side by side: -10 to 50 CEL (with no icing or condensation) Storage: -25 to 70 CEL (with no icing or condensation)
Ambient humidity	Operating: 25 to 85% RH Storage: 25 to 85% RH

**Characteristics**
Total accuracy	Accuracy of operating time and setting error (including temperature and voltage influences) Power-ON start: +/- 0.01% +/- 50 ms max. Signal start: +/- 0.005% +/- 30 ms max. Signal start: +/- 0.005% +/- 3 ms max. (The value is applied for a minimum pulse width of 1 ms.) The values are based on the set value.
Insulation resistance	100 MOhm min. (at 500 VDC) between current carrying metal parts and exposed non-current carrying metal parts, between non-continuous contacts
Dielectric strength	between current-carrying metal parts and non-curernt-carrying metal parts: 2000 VAC 50/60 Hz for 1 min between input and control output and operation power circuit: 1000 VAC 50/60 Hz for 1 min between non-continuous contacts: 1000 VAC 50/60 Hz for 1 min
Impulse withstand voltage	between power terminals: 1 kV between current-carrying terminals and exposed non-curernt-carrying metal parts: 1.5 kV
Noise immunity	Between power terminals: +/- 1.5 kV Between input terminals: +/- 600 V Square-wave noise by noise simulator (Pulse width: 100 ns/1 us, Rise: 1-ns)
Static immunity	Mulfunction: 8 kV ,Destruction: 15 kV
Vibration resistance (Destruction)	10 to 55 Hz, 0.75 mm single amplitude in each 3 directions for 2 hours
Vibration resistance (Malfunction)	10 to 55 Hz 0.35 mm single amplitude in each 3 directions for 10 min
Shock resistance (Destruction)	300 m/s**2, in each 6 directions (3 axes) 3 times
Shock resistance (Malfunction)	100 m/s**2, in each 6 directions (3 axes) 3 times
Degree of protection	IEC60529(JEM): Panel surface: IEC IP66, UL508 Type 4X (indoors) (when using the Y92S-29 Waterproof Packing and Y92F-30 Flush Mounting Adapter), Case rear: IP40, Terminal block: IP20
Applicable standard (UL)	Standard No.: UL508 File number: E41515
Applicable standard (CSA)	Standard No.: CSA C22.2 No.14 File number: LR22310
Applicable standard (VDE)	VDE0106/P100
Applicable standard (EC Directive (Machinery Directive) )	EN61812-1
Applicable standard (EC Directive (Low Voltage Directive) )	EN61812-1
Applicable standard (EC Directive (EMC Directive) )	EMI: EN61812-1 Emission Enclosure: EN55011 Group 1 class A Emission AC mains: EN55011 Group 1 class A EMS: EN61812-1 Immunity ESD: EN61000-4-2 (6 kV contact discharge (level 2), 8 kV air discharge (level 3)) RF-interference: EN61000-4-3 (10 V/m (Amplitude-modulated, 80 MHz to 1 GHz) (level 3), 10 V/m (Pulse-modulated, 900 MHz 5 MHz) (level 3)) Immunity Conducted Disturbance: EN61000-4-6 (10 V (0.15 to 80 MHz) (level 3)) Immunity Burst: EN61000-4-4 (2 kV power-line (level 3), 1 kV I/O signal-line (level 4)) Immunity Surge: EN61000-4-5 (1 kV line to lines (power and output lines) (level 3), 2 kV line to ground (power and output lines) (level 3))
Applicable standard (Others)	Immunity Voltage Dip/Interruption: EN61000-4-11 (0.5 cycle, 100% (rated voltage))
Mounting method	Flush mounting / Surface mounting
external connection method	11-pin round socket
Case color	Black (Munsell N1.5) (The front part can be changed to light gray or white in sold separately panel)
Attachment	Label for DIP switch settings
Accessory (sold separately)	Soft Cover (Y92A-48F1) Hard Cover (Y92A-48) Flush Mounting Adapter (Y92F-30) Flush Mounting Adapter (Y92F-45) Waterproof Packing (Y92S-29) Replacement Front Panel (Y92P-CXT4S) Replacement Front Panel (Y92P-CXT4G) Replacement Front Panel (Y92P-CXT4B)
Weight	Approx. 115 g